Limited Liability Company “Arkada-MB”Address: 35, Krasninskoe shosse, Smolensk, 214030, Russia
Phone/fax: +7 (4812) 65-26-99, 66-07-61.
INN: 6730050654, KPP: 673001001, Acc: 40702810628000000421 in FKB UNIASTRUM BANK in Smolensk, Correspondent account: 30101810400000000850, Bank Identity Code: 046614850, OKPO: 70841391, OKONH: 14230
Press Forming Punching
Automated forming and punched complexes are working out of the «Arkada-MB» design office. They are made under steadfast control of the leading experts-designers specializing on working out of the similar equipment. Depending on characteristics of processed metal and the requirements to the production, «Arkada-MB» Ltd. projects and realizes following types of complexes:
- Forming complexes
- Punched complexes
Forming complexes
Forming complexes are intended for manufacturing of details by a method of punching from sheet metal (strip), prepared in advance on a transverse cutting line. The configuration of details can be diversified from simple, type of washers, to difficult ones. These details can be flat with the edges unbent under corners; with punching, stamping and etc. Important difference between a forming complex and a punched one is that it makes a ready-made product. Depending on the kind of the production defined by the customer (we can make the production according to the sketch of the customer), the complex structure can be changed. Configurations of complexes and structure of units and mechanisms are defined by technical project working out.
We bring to your attention typical characteristics of a forming complex:
(Characteristics can be changed depending on wishes of the customer and a kind of the production)
Forming complex for manufacture of cross connection part
The forming complex is intended for manufacturing of stamped details and concerns the equipment of processing of thin-gauge steel by pressure. Manufacturing of details is made from rolled metal by punching in a semi-automatic mode.
Basic characteristics:
| Mode of operation | Semiautomatic |
| Mode of a tape lace-up from a roll | Semiautomatic |
| Mode of readjustment of a feed pitch | Manual |
| Billet material | Galvanized steel |
| Line width: | |
| — minimum, mm | 80 |
| — maximum, mm | 305 |
Line thickness, mm |
0,5..2,0 |
| Max outer diameter of rolls, mm | 1500 |
| Internal diameter of rolls, mm | 500..600 |
| Max weight of a roll, kg | 2800 |
| Feed speed of a tape by feeding device, m/min | 4,5 |
| Feeding drive | Electromechanical |
| Power of a power circuit | 220/380 V; 50 Hz |
| Complex rated capacity without a press, kilowatt | 1,1 |
| Overall dimensions taking into account a press: | |
| — length, mm | 6870 |
| — width, mm | 2500 |
| — height, mm | 2500 |
Weight of a complex no metering a press, kg |
3000 |
| Quantity of serving workers in a shift | 2 (1 setup man и 1 operator) |
| Shift-working arrangement of complex work | 2 |
Punched complexes
Punched complexes are intended for making of a great number of holes in a tape material (candy), prepared in advance on a transverse cutting line. The tape with punching is used for the further rolling in forming lines and reception of bent profiles: a punched corner, a beacon for plaster, profiles for «wet» furnishing of facades, racks of the commercial description, racks of warehouse systems and etc. Automated complexes for punching of fixing products and strip punching can be completed, depending on requirements to a made product, units of leading firms-manufacturers («Herrblitz», «JOINT»). Configurations of complexes and structure of units and mechanisms are defined by technical project working out.
We bring to your attention typical characteristics of a punched complex:
(Characteristics can be changed depending on wishes of the customer and a kind of the production)
The forming complex for tape punching is intended for making holes in a metal tape.
Basic characteristics:
| Mode of operation | Semiautomatic |
| Mode of a tape lace-up from a roll | Semiautomatic |
| Mode of readjustment of a feed pitch | Manual |
| Billet material | Galvanized steel |
| Line width: | |
| — minimum, mm | 20 |
| — maximum, mm | 75 |
Line thickness, mm |
0,4..0,6 |
| Max outer diameter of rolls, mm | 1500 |
| Internal diameter of rolls, mm | 600 |
| Max weight of a roll, kg | 2800 |
| Feed speed of a tape by feeding device, m/min | to 4,5 |
| The maximum feeding stroke, mm | 200 |
| Feeding drive | Electromechanical |
| Power of a power circuit | 220/380 V; 50 Hz |
| Complex rated capacity without a press, kilowatt | to 5 |
| Overall dimensions taking into account a press: | |
| — length, mm | 8000 |
| — width, mm | 2500 |
| — height, mm | 3000 |
Weight of a complex no metering a press, kg |
3000 |
| Quantity of serving workers in a shift | 2 (1 setup man и 1 operator) |
| Shift-working arrangement of complex work | 2 |